1. A Needle within Cap for locking the glue
2. New HDPE Material.
3. Good sealing.
4. Odorless and Nontoxic.
There is always one type adhesive for thread that you may need below.
222 Threadlocking adhesive
Low strength,thixotropic viscosity.,
Suitable for most metal surfaces,Parts can be disassemble with hand tools.
Ideals for fasteners diameters of M6 and smaller,controlled lubricity can attain accurate clamp loads.
242 Threadlockong adhesive
General purpose,thixotropic viscosity.For locking and sealing M6-M20 threads.
Parts can be separated using hand tools,controlled lubricity,can attain accurate clamp loads.
243 Threadlocking adhesive
Oil resistant,medium strength
Fast curing,used on inert surface,improved oil tolerant,easy to disassemble,can be applied on surfaces with oil
For fasteners smaller than M20
262 Threadlocking adhesive
Medium to high strength
Thixotropic viscosity,excellent chemicals resistance.
Suitable for most metal surfaces, for fasteners smaller than M20.
A permanent threadlocker,Excellent for preventing rust and corrosion in extreme chemical/environmental conditions.
271 Threadlocking adhesive
High strength,low viscosity.
For permanent locking and sealing,fasteners smaller than M36
Heating and tools required for disassemble.
272 Threadlocking adhesive
High temperature,high strength
Withstands temperatures up to 230 °C
For locking and sealing the thread of cylinder
Provides a fast cure on most surfaces,including the part without being cleaned .
Recommended for bolts up to M36.Heating and hand tools required for disassemble
277 Threadlocking adhesive
High viscosity,excellent chemicals resistance.
For permanent locking and sealing bolts up to M36
Prevent rust and corrosion of threaded fasteners.Heating and hand tools required for disassemble.
290 Threadlocking adhesive
Medium strength,low viscosity,fast curing.
For locking and sealing pre-assembled bolts M2-M12.Also for sealing welds and porous metal parts.
Prevent rust and corrosion.Heating and tools required for disassemble.
The adhesive is high purity, non solvent-based,and completely safe.
We can adjust the raw materials or synthesis method to achieve the viscosity you desire: anywhere from 2-1,000mPa·s (25°C).
10ml 50ml 250 ml Anaerobic sealant adhesive ,Threadlocker / Henkel / Loctit 243 242 222 260 262 270 290 2400
1) Remove the oil and grease from the surfaces to keep it dry and clean
2) the threads should be coated enough glue until filling the whole gap. the best coating ways is coating the threads with a thin film with 0.05mm
3) Tighten the thread and wipe off the excess adhesive
4) After 15 minutes curing, you will have the initial bonding strength and after 24 hours, you can get the full bonding strength.As one of the largest supplier for Loctite adhesive Products,we can also supply:
1.Loctite threadlocker Number: loctite 222 242 243 262 260 263 277 271 272 290,207(10ml bottle 50ml bottle or 250ml bottle)
2.Loctite instant adhesive number: loctite 401,406,495,496,414,416,415,460,403,435 ,4860,480, 410,4011,4014,454,409 (20gm bottle or 500gm bottle)
3.Loctite pipe thread sealant/ flange sealant number: loctite 587,596,598, 595,5900,5910, 5920, 5699,593 , 542,545,569,577,567, 510,515,518
4.Loctite retaining compound number: loctite 601,603,609,620,638,648,680,649,6300 (10ml bottle, 50ml bottle,250ml)
5.Loctite silicone sealant number: loctite 5900 596 595 5699 5910 5920 587 595 593 85g 300 ml
6.Loctite hysol epoxy adhesive number: loctite e-20hp, loctite e-120hp, loctite e-60hp, loctite e-30cl, loctite e-40fl
7.Loctite treatment: loctite C5-A, loctite 76764, loctite 7063, loctite N-5000, Loctite N-7000, Loctite 770